Medelec/TECA - Synergy EMG System T2
Medelec/TECA Synergy EMG System T2 Forums
When I open the program, I get a warning, warning 1012 unable to open the system log file. Logging has been disabled. Then when I try to open up nerve conduction studies, I get the error message that the parameter is incorrect. Are there any solutions to these error messages? Thank you!
RE: Medelec/TECA - Synergy EMG System T2Hello,
Is there any solution for converting EMG signals reordered using Medelec Synergy EMG system to be readable by MATLAB?
Thanks
RE: Medelec/TECA - Synergy EMG System T2I used Medelec in Sweden 1979-1982 and TECA in USA 1984-1990 in my research. Later I have been using EMG recorders of different types but none of those have adustable filter settings like the old Medelec system had. I am now looking for surface EMG recording equipment with adjustable filter settings to use in rearch and wonder what you have to offer. Please send me an email so weI can discuss options
Sven E Widmalm, Dr. Odont.
1565 Kuehnle, Ann Arbor, MI 48103. Phone 734-663-3664
RE: Medelec/TECA - Synergy EMG System T2
deluxe stimulator probe defective. Need to replace now.
Machine working fine.
Have all components including foot pedals
Where can I get another NCV stimulator probe??
Rob Oshinsky, MD
3014837558, EST
RE: Medelec/TECA - Synergy EMG System T2I have a TECA Synergy VIASYS Healthcare EMG machine that the computer has crashed on. We have replaced the computer, but need the software to reinstall. Where could we get a CD?
RE: Medelec/TECA - Synergy EMG System T2My CD was damaged.How can I get another one.I have a license and need a source for the programme
RE: Medelec/TECA - Synergy EMG System T2I have a medelec TECA synergy EMG machine (vintage 2002), running version 10.1 Synergy system software on a Windows XP box. I bought the machine from the practice where I had used it.
The disk crashed, so I replaced it and reinstalled the software from the distribution disks. But when I run the Synergy application, a diaglog box pops up prompting me for the sotware license number. The number stamped on the hug of the CD ROM doesn't work, nor does the hardware serial number. I understand Oxford Instruments orphaned this model long ago.
Where can I find this license number, or otherwise get this machine running again?
RE: Medelec/TECA - Synergy EMG System T2I have an EMG Medelec Synergy N2 working on windows XP. I would like to change but I did not find who to contact in France. The phone Number I had is not good.
Thank you for your help
Dr Eric de Bisschop (Aubagne - France
RE: Medelec/TECA - Synergy EMG System T2Our machine is locked and we can not access to the program for NCV-ENG test. Also the conduction velocity in the motor nerves is to hight so I think that we need the test configuration. Also we need to configure the report leyout. We would like to know if you have a teechnician who can come into our sytstem throught the red (internet) to help us and How much is going to be charged for that service. our machine is a TECA/MEDELEC/SYNERGY= Serial Number 050636 and PART NUMBER 55-040W002-B
We appreciate your help,
Elda Diaz
RE: Medelec/TECA - Synergy EMG System T2I think my hard drive on my machine crashed. Can you help me find a local tech to see if it is repairable?
717-718-9459
RE: Medelec/TECA - Synergy EMG System T2